Do not forget to check these parts after the car wading
Since entering this year, heavy rainfall, dust storms, floods and floods have covered many provinces and frequently occurred. According to incomplete statistics, heavy rainfall from Liuzhou, Guangxi Province to the recent torrential rain in Wuhan has caused hundreds of vehicles to be flooded. Now Typhoon No. 1 "Nibert" has landed and is said to have been "Pyramid". A wide range of precipitation has caused traffic problems. The most painful thing is that many drivers and users suffer damage due to heavy rain! So what parts of the car need to be checked after wading, so as to prevent the car from being damaged for the second time? Spare position for spare tire Many spare tires for family cars are located in the depressions below the floor of the trunk, and the positions where spare tires are placed in the trunk are usually provided with a plurality of vents communicating with the outside. These vents communicate with the outside of the vehicle. If the depth of accumulated water reaches the height of the spare tire, the water will enter the tail box from the vent, and then flow into the rear seats, soaking the seat cushion to induce mildew. Steering gimbal cage There is a dust jacket around the universal joint ball cage. If the dust jacket is damaged, the water will enter the universal joint ball cage when the vehicle wading. The most direct effect is that the vehicle loses direction and assists, even when the situation is serious. Caused the direction of stuck. It is necessary to remove the infiltrated water, refill the lubricant and replace the boot. Harness interface There are many wiring harnesses in the engine compartment that are covered with insulating and heat-resistant materials. These different types of wiring harnesses have high and low positions. When the vehicle is wading, the low-position harness interface is easily immersed in water, so it needs to be dealt with in time. Otherwise, there will be sporadic failure of the car circuit in the future, which will affect the normal driving of the vehicle. engine Some cars have low engine intakes, and water enters the intake passage through the air intake. First, the negative battery wire must be removed as soon as possible to prevent short circuiting of various electrical appliances on the vehicle due to water ingress. Check if there is water in the cylinder of the engine. Water will cause the connecting rod to bend and damage the engine. The position where the air filter is located is the gateway of the engine. When the vehicle wades, if it is found that the air filter element is wet, it means that water enters the air intake pipeline and the internal water intake of the engine needs to be checked in detail. Otherwise, the power of the vehicle is also Will be subject to certain influence. The high temperature generated by the vehicle during the braking process will evaporate a large amount of water vapor, and the braking system has a very strong adsorption force. When the automobile is wading, the brake fluid can easily enter the water. Affects the braking effect, and may also cause the brake to malfunction. Lights The headlights are important equipment for driving in rain and fog and at night. It is easy to see if the water is in. If the shade of the lampshade is not good enough, the water can easily be poured into the lights when the vehicle wading. The formation of water mist in the lamp affects the transmission effect of the light. It should be decided as soon as possible based on the working status of the lights to clear the water mist or replace the lights. What is the wading height of the car? In general, most vehicles do not exceed a depth of 30cm, which is basically half the height of the wheel, and for the critical intake part, the general height is about 70cm. Another situation is that if you encounter wading traffic, unfortunately your car suddenly shut down, this situation must never be the second start! Obedient, honestly call the trailer, go to the repair shop to remove the air intake and four spark plugs, and then check the crankshaft. If there is no problem with the crankshaft, it is better to drain the cylinder and install it.
93% Purity Medical Oxygen Generator is the Oxygen Generator manufactured for hospitals, clinics,etc.These places were normally
supplied with cylinder oxygen. But for some area, cylinder oxygen is
expensive and difficult to transport. This 93% purity Medical Oxygen Generator
is able to fill cylinders at site. Some customer use the 93% purity oxygen directly to hospital centralized oxygen supply system. The whole product has air
compressor, air treatment part, air tank, oxygen separator and oxygen
buffer tank. It is easy to install, easy to operate, fast to produce
quolified oxygen.
93% Purity Medical Oxygen Generator 93% Purity Medical Oxygen Generator,Medical Oxygen Generators For Hospital,Purity 93% Psa Medical Oxygen Generator Shandong Gamma Gas Engineering Co. Ltd. , https://www.gammagas.com
