High-lift truck operation specification
The hydraulically-powered manned aerial vehicles are contemporary advanced species mechanical equipment. The construction workers use the aerial vehicles to lift off the work. As long as they are used correctly, safety is guaranteed. However, it is not a proper operation or security measures have not been implemented. It is also a very dangerous work-at-height operation. The following rules of conduct have been formulated. 　　 1. Motorists must hold a bus driving license. 　　 2 , auxiliary transmission must be separated from the hydraulic pump. 　　 3 , pay attention to the height of bridges and tunnels. 4 , the speed is generally not more than 30 km / h, the suburb does not exceed 40 km / h. 5 , the operation bucket (platform) declined to stay in the staff. 　　 1. The choice of parking position should be a solid ground, the inclination of the vehicle should not exceed 3° , and the warning light should be turned on. 　　 2, the wind working height 　　   Wind 6 or below suitable height 10 meters below the operation; 　　   Wind power level 5 can work below 11~20 meters ; 　　   Wind 4 and below suitable height 21 to 30 meters below the operation. 　　 3, starting the pump, auto clutch depressed, pull handbrake, gearbox in neutral, the clutch lever pulled hydraulic pump, the hydraulic pump is in operation. 　　 4. After the hydraulic oil pump runs for 2~5 minutes, it can operate the handles of each movement. 　　 5 , the operation of aerial vehicles, should be trained and hold personnel responsible for operational licenses. 　　 6. The operators must concentrate on the prevention of misoperation and strict operation of alcohol prohibition. 　　 7 , first put down the legs, if necessary, put the pad under the leg of the leg to ensure that the vehicle is in a horizontal state. 　　 8. When operating the handle, it should be steady, and do not swift and swift in order to avoid the inertial swing of the working arm and the accident. 9. Operate in strict accordance with the technical parameters and operating ranges specified by the equipment. 10 , the work bucket (platform) on the staff to fasten the seat belts. 11. When lifting the work bucket (platform), the upper and lower arms should be alternately operated to ensure that the bucket (platform) is in the best radiating radius. It is forbidden to use the arm for other purposes. 　　 12. When operating, the operator should pay attention to the platform (platform ) Safe distances between arms and high and low voltage wires, telephone lines and buildings, big trees, billboards, lighting, etc. 13, when the value of the driver, responsible for the ground and pay attention to work safety contacts of the vehicle. 　　 14, using a working height 25 m or more vehicles, in addition to set up safety signs and guardrails, ground guardian addition to the driver, but also set up a dedicated intensive care 1-2. 　　 15, during operation, the hydraulic system if found abnormal noise or sudden oil leakage, it should stop the work until after the inspection or repair, can continue to work. 　　 16, a hydraulic system failure, when the arm can not move, should try to make a job hopper (platform) on the safe evacuation of staff and inform professional maintenance staff. 　　 17, operation is completed, the job hopper (internet), reset the arm, leg away and disengaging hydraulic pumps, release the parking brake before starting the driving. 　　 1. The working bucket (platform) for high-altitude operation, the arm and leg should have reflective safety signs. 　　 2, aerial vehicles should be equipped with a triangular (tires) two skids and skid legs 4, the device should board level flag. 　　 3. The most common aerial platforms currently on the market include: Dongfeng Aerial Work Trucks, Liberation Aerial Vehicles, Ao Ling Aerial Work Vehicles, Qingling Aerial Work Trucks, Jiangling Aerial Work Trucks, and JAC Aerial Work Trucks. Mainly used in electricity, communications, street lamps, traffic police, highways, cable television, ship repair, construction, gardens, advertising, photography, large enterprises and other industries. Xigong Chusheng professional aerial vehicle manufacturer, the conventional aerial vehicles are: Freka aerial vehicles Jiangling Shunda aerial vehicles Isuzu aerial vehicles Dorica high altitude vehicles 12-14 meters 16 meters aerial vehicles Dongfeng Tianjin Lift truck hydraulic lift truck
2020 latest hotsale 7" touch screen static desktop inkjet printing machine for all kind of packaging is convenient to operate Chinese, English, Number, Date, Time, varaaible QR Code and Bar Code, Picture on variety of product packages, tube, bottle, cable, bag, pouch, electric product et.
This machine is almost completely free maintenance,in order to offer a wonderful using experience for our customers , we will send an operation file and videos to users, incase there is any problem during suing, we provide lifetime technical support.
desktop inkjet printer, table top inkjet coder, inkjet coding machine Wuhan HAE Technology Co., Ltd. , https://www.whinkjetcodingmachine.com