Taiwan's injection molding machine has created a research and development of high-performance rubber and plastic models
Deep Groove Ball Bearing,
formerly known as single-row centripetal ball bearing, is the most widely used
rolling bearing. It is characterized by small frictional resistance and high
speed, which can be used to bear the combined load of radial load or radial
direction and axial load, and also can be used to bear the axial load.
The basic type deep groove
ball bearing consists of an outer ring, an inner ring, a set of steel balls and
a set of cage. .Deep groove ball bearing type has a single row and double row
two kinds, deep groove ball structure is sealed and open two kinds of
structure, open type means without seal, seal type deep groove ball bearing
also have dust seal and oil seal. The dustproof sealing material is sheet metal
stamping, only simple to prevent the dust from entering the bearing raceway. The
oil-proof type is contact oil seal, which can effectively prevent the grease out
of the bearing.
Deep groove ball bearing type:
deep groove ball bearing
(60000 type);
Deep groove ball bearing with
stop groove in outer ring (60000N type);
Deep groove ball bearing with
a dustproof cover and a stop groove on the other side.(60000-ZN type)
Deep groove ball bearing double
cover with dustproof cover and with stop groove in outer ring (60,000-2zn type);
Deep groove ball bearing with
dust cover (60000Z);
Deep groove ball bearing with
dust cover on both sides (60,000-2z);
Deep groove ball bearing with
seal (60,000-ls type, 60,000-rz type);
Deep groove ball bearing with
seals on both sides (60,000-2ls, 60000-2rz);
Deep groove ball bearing with
flange (F60000 type);
Deep groove ball bearing with flange
andone side dust cover(F60000-Z type).
Deep groove ball bearing with flange
and both sides dust cover.(F60000-2Z).
Application:
Deep groove ball bearing can
be used for gearbox, instrument, motor, household electric appliance, internal
combustion engine, transportation vehicle, agricultural machinery, construction
machinery, construction machinery, roller skating shoes, yo-yo-ball, etc.
We believe that we can supply
the best service and price for your, hope to make a long-term cooperation with
you. If you have any question please do not hesitate contact with us. We keep
warmly welcome you visit us in any time.
Deep Groove Ball Bearing Deep Groove Ball Bearing,Wholesale Deep Groove Ball Bearing,High Precision Deep Groove Ball Bearing,Stainless Steel Deep Groove Ball Bearing LUOYANG AUTO BEARING CO.,LTD , https://www.ballbearing.nl
Injection molding machine blooms
At the 2006 Taipei International Rubber & Plastics Industry Exhibition, Hu Yongjin, the convener of the Plastics and Rubber Machinery Committee of Taiwan District Machinery Association and President of Bioplastics, bluntly stated that under the pressure of recession, Taiwan's injection molding machines have created high-performance models for research and development. .
Taichung Seiki introduced a Vα-150-Hybrid electric hybrid injection molding machine with servo control as its main structure. The difference between this machine and the traditional hybrid electric injection molding machine is that the former has the characteristics of energy saving, rapid and stable all-electric injection molding machine, and is supplemented with an accumulator to store oil pressure energy, so that the injection speed reaches up to 1200 mm/ Seconds, thus minimizing energy consumption. Lin Fuquan, Taiwan marketing manager of Taichung Seiki Plastics Machinery Co., Ltd., said that this machine is particularly suitable for computers, telecommunications and electronics industries to produce high-viscosity or thin-meat plastic products such as memory cards, IC cards, and battery boxes.
The high-speed injection molding machine launched by Bioplastics has an injection speed of 1500 mm/s and good product quality. Hu Yongjin showed reporters the PC-made card shell card produced at the exhibition site. Even if it is strongly bent, it does not It will break, and the main reason lies in the design of the pressure-keeping system.
The all-round CLF-180TX pressure multi-circuit was developed to shorten the processing time and reduce production costs. For example, PET preforms with a diameter of 32 mm and a weight of 75 grams were produced, with a 1-cavity 48 cavity and a cycle time of only 28 seconds. .
Nanxun developed a BMC injection molding machine, according to Lai Shusheng, general manager of the company, and its price is half as cheap as foreign models. There is also a double-template pin-die injection molding machine, which uses a new clamping mechanism and only contains two templates. Therefore, the machine table can be shortened by 30%, and the machine table is also lighter, which helps reduce the investment cost of the plant.
In the two-color, multi-color molding machine, Quan Lifa, Baisu, Nanxun, Zhenxiong and other products have products. Among them, the Nanxun TNRX-230 dual-color machine adopts a fixed mold base and a replaceable mold. Since only the mold is replaced, the cost of the mold can be reduced, and Lai Shengsheng cannot speak the traditional 1/3. As for the features of Zhenxiong direct-pressure two-color injection molding machine, there is a turntable with a reciprocating 180 degree rotation on the second board, which can be equipped with a set of two-color molds or two sets of molds for double-material/two-color injection molding.
As for all-electric injection molding machines, many manufacturers such as Taichung Seiki, Zhenxiong, and Qunji have exhibited. It is reported that Taiwan has established an all-electric injection molding machine research and development alliance. Wang Zhengqing, deputy director-general of the Taiwan Machinery Industry Association, predicts that all-electric injection molding machines with high injection speed, low ejection power, low forming cycle, energy saving, cleanliness, low noise, and easy maintenance will be widely used in computers and electronics. Telecommunications, medical equipment, precision machinery and other high value-added industries.
Blow molding machine high speed and high quality
The Fengji Iron Works focused on the HBS series of high-speed hollow molding machines this year, which can be used to produce 10 to 20 liters of square and round barrels. According to Wei Canren, vice chairman of the company, the performance of this machine has been improved. Taking a 20-liter barrel as an example, the production cycle is only 27-28 seconds per hour, which means 120 per hour. The finished product meets international container standards.
Wanglin Machinery's Beaver-B series compact injection blower has the advantages of one-time molding and no waste. It has a multi-cavity membrane and a maximum of 1 membrane and 16 chambers. The finished product bottle is smooth and has high thread accuracy, eliminating the need for secondary processing. Processing time is only 4.5 seconds. The finished product can be up to 2 mm in thickness and 1 liter in maximum capacity. The machine is suitable for the manufacture of medicine bottles, cosmetic bottles, beverage bottles, detergent bottles and the like.
Peripheral equipment improves factory automation
Taiwan's peripheral equipment manufacturers include Taiwan Meide, which produces measuring machines, proportional valves, mold temperature machines, and dryers, and Yuding, which produces cooling equipment and mold temperature machines. Fuwei Seiki, which produces a variety of rapid die change systems, developed a fully automatic die change carriage. The car platform is controlled by a single button, and the mold can be moved into or out of the machine fully or semi-automatically. Xiao Wenlong, president of Fuwei Precision Machinery, stated that this aircraft is the only model-changing trolley developed in Taiwan and the mainland at present, and the price is about 60% of that of similar models in Japan.
Continuing the "Research, Development, and Innovation Products" Contest
In order to encourage Taiwanese companies to invest in R&D, the Taiwan Machinery Industry Association continued to organize “research, development and innovation products†contests and became a major feature of the Taipei Plastics Industry Exhibition. For this year's list of winners, please see the Adsale Network (Taiwan-Ronge Outcomes Award for Plastic Machinery R&D Innovation Products Competition).
In addition, Feng Kewen, chairman and general manager of Feng Ke, encouraged the industry to apply the knowledge management system to achieve knowledge transfer through information management to enhance the added value of the company.